６３０３Lyot filter
Specification of 0.125Å/6303Å Lyot filter
1. Central working wavelength 6302.50Å
2. FWHI (Full width in half intensity) 0.125Å
3. Tuning range ±0.5Å or ±(4 x FWHI)
0.02Å/step
by 5 inside tuning elements
4. Clear aperture φ30mm, φ32mm for both sides
5. Off-axis angle: 1°
6. Working temperature 45℃
7. Stability of working temperature in the filter center ±0.01℃
8. Permissible ambient temperature -5 to +40℃
9. Transmisivity 3%
10. Warming-up time 1 hour starting at 20℃
11. Uniformity of transmission on full clear aperture better than 90%
12. Thermal controller enclosed inside the filter housing
13. Contour size 58(L)x18(W)x22(H)cm
14. Weight Ca.30kg
15. Power supply 100V, 50/60Hz
16. KD*P modulator:
KD*P of wide field of view:
a. Clear aperture: φ34mm
b. Transmission: 60%
17. Isolated interference filter provided by USA:
Clear aperture: >φ35mm
FWHI 30Å
Peak transmission >45%
Working temperature 35℃
18. Polaroid sheets used for Lyot filter are provided by Polaroid Co. of Japan:
Type: HN42
Transmission for polarized light 80.5%
Quantity: 8 pcs.
19. Silicon oil used for Lyot filter is provided by Japan Branch of Dow Corning
Co.
20. Cable: 10m+15m between filter to controller,
for which an interface for long cable is provided
Specification of KD*P & 6303Å Lyot filter electric controller
A.Thermal controller unit
1.Contour size
enclosed inside the filter housing
2.Working temperature
45 degree(C)
3.Stability of working temperature in the filter center
+/-0.01 degree(C)
4.Warming-up time
1 hour starting at 20 degree(C)
5.Heater protection circuit
Provided, when over 46 degree(C), raise alarm.
B.Filter controller unit (Thermal controller panel unit)
1.Control functions(Remote/Manual) & Indicator
(Remote/Manual) & Indicator
2.Contour size
<25.5(W)x18(D)x12(H)cm
3.Form
According to the international standard
4.Weight
<10Kg
5.Power supply
100V, 50/60Hz, +/-10% , 2P+Ground plug (plug is supplied)
6.Power consumption
Quickly heating: 60VA, constantly heating: 10VA
7.Color
Ivory (or milk-white) color
8.Interface Cable
RS-232C D-sub 9pin
Cable : Refer to a drawing.
for which an interface for long cable is provided.
9.Standard conformity
As the voltage of both filters is rather low (30V or lower),
so there will not be any problem in insulation.
Also there will not be any harmful radiation electric wave.
10.Function
Pass Band Tuning
Adjust : +Button,-Button(0.02A Up/Down)
Display: Numeral
Remote : Enable by RS232C
C.Power supplier for KD*P
1.Output voltage range
500 to 1400V
2.Output wave shape
Rectangular
3.Output Automatically Cut-Off
When high DC voltage feeds on KD*P with a long time over 2 seconds
4.Control functions(Remote/Manual) & Indicator
(Remote/Manual) & Indicator
5.Contour size
<20(W)x30(D)x15(H)cm
6.Form
A small case, less than 1.5m apart from the KD*P inside the telescope,
as the high voltage power supply must be placed near the KD*P as
possible.
7.Weight
<5Kg
8.Power supply
100V, 50/60Hz, +/-10%, 2P+Ground plug (plug is supplied)
9.Power consumption
<35VA
10.Color
Ivory (or milk-white) color
11.Interface
HTL(0 or +10V) Centronics parallel 36pin female.
Cable : Refer to a drawing of electric.
for which an interface for long cable is provided.
* Interface pin assignment
Pin No. Signals contents
1 Ground
2 PC1 Output control(From a computer)
3 PC2 Output control(From a computer)
4-18 Reserved
19 Ground
20 V1 Output status (To a computer) Detect High Voltage
21 V2 Output status (To a computer) Detect High Voltage
22-24 Reserved
25 AL1 Alarm High Voltage Power fed > 2seconds
26-36 Reserved
12.Function
To adjust voltage, use dial front of the power supplier controller panel.
13.Standard conformity
As the voltage of both filters is rather low (30V or lower),
so there will not be any problem in insulation.
Also there will not be any harmful radiation electric wave.
Only the voltage to KD*P is rather high, however, as the resistance
of the KD*P is very big (above 10 Meg Ohm), so the current through
KD*P is negligibly small, so there will not be any harmful radiation
electric wave.
６５６３Ｈα Lyot filter
Specification of 0.25Å/6563Å Lyot filter
1. Central working wavelength 6562.81Å
2. FWHI (Full width in half intensity) 0.25Å
3. Tuning range: ±1.5Å or ±(6x FWHI),
0.02Å/step,
by 5 inside tuning elements
4. Clear aperture φ30mm, φ32mm on both sides
5. off-axis angle 1°
6. Working temperature 45℃
7. Stability of working temperature in the filter center ±0.01℃
8. Permissible ambient temperature -5 to +40℃
9. Transmisivity 5%
10. Warming-up time 1 hour starting at 20℃
11. Uniformity of transmission on full clear aperture better than 90%
12. Thermal controller enclosed inside the filter housing
13. Contour size 46(L)x18(W)x22(H)cm
14. Weight Ca.17kg
15. Power supply 100V, 50/60Hz
16. Isolated interference filter provided by USA:
Clear aperture: >φ35mm
FWHI 30Å
Peak transmission >45%
17. Polaroid sheets used for Lyot filter are provided by Polaroid Co. of Japan:
Type: HN42
Transmission for polarized light 80.5%
Quantity: 7 pcs.
18.Silicon oil used for Lyot filter is provided by Japan Branch of DOW Corning
Co.
19. Cable: 10m+15m between filter to controller,
for which an interface for long cable is provided
Specification of 6563A Lyot filter electric controller
A.Thermal controller unit
1.Contour size
enclosed inside the filter housing
2.Working temperature
45 degree(C)
3.Stability of working temperature in the filter center
+/-0.01 degree(C)
4.Warming-up time
1 hour starting at 20 degree(C)
5.Heater protection circuit
Provided, when over 46 degree(C), raise alarm.
B.Filter controller unit (Thermal controller panel unit)
1.Control functions(Remote/Manual) & Indicator
Remote and Manual & indicator
2.Contour size
<25(W)x18(D)x12(H)cm
3.Form
We will use the controller case according to the international
standard
4.Weight
<10Kg
5.Power supply
100V, 50/60Hz, +/-10% , 2P+Ground plug (plug is supplied)
6.Power consumption
Quickly heating: 60VA, constantly heating: 10VA
7.Color
Ivory (or milk-white) color
8.Interface Cable
RS-232C D-sub 9pin
Cable : Refer to a drawing of electric.
for which an interface for long cable is provided.
9.Standard conformity
As the voltage of both filters is rather low (30V or lower),
so there will not be any problem in insulation.
Also there will not be any harmful radiation electric wave.
10.Function
Pass Band Tuning
Adjust : +Button,-Button(0.02A Up/Down)
Display: Numeral
Remote : Enable by RS232C
３．10830 fabryperot etalon filter
Specification of an etalon fabricated "y-cut" lithium niobate
Characteristics
・substrate diameter 75mm thickness 220 micron (maximum free aperture 65 mm)
・operating wavelength 1083 nm
・finesse at 1083 nm to be at least 25 over central 50 mm
・Full width in half intensity 0.5Å
Note: anti-reflection windows are required on either side of the etalon.
Units includes
・Etalon, in simple perspex cell with HV supply connector
・Prefilter
・Transport, Insurance & container
Conditions
a. The width of transmission change by the temperature
The refractive index for the O-ray changes by about 2E-6 per degreeC.
The coefficient of expansion is about 1.6E-5 per degreeC.
b. The tuning range of above and the characteristic of stability
At 1083nm the tuning range of the etalon for +/- 5kV is about 0.32 orders.
c. Attached documents
User's manual, Test report for warranty, Contour drawing
(We hope to get Contour drawing asap, for design of mount to telescope)
d. Show the Operating voltage for transmission of center of 10830Å.
e. Prefilter's diameter is 50mm (clear aperture 46mm)
４．CaⅡ-K etalon filter
Specification of 1.0Å/3934Å filter
1. Central working wavelength 3934Å
2. FWHI (Full width in half intensity) ＜1.0Å
3. Clear aperture φ100mm
4. Weight Main: 1360g
Blocking: 480g
5. Contour size Main: φ137mm×L65mm
Blocking: φ85mm×L89mm
6. Stability of working temperature Main: ＜1Å/300℃
Blocking: ＜1Å/40℃
